Ghost 2 Immobiliser Reviews
The Ghost 2 immobiliser utilizes cutting-edge technology to prevent car theft. This discreet device is unnoticeable by thieves and only turns on the engine after a PIN or app is entered.
It is weatherproof and connects to the CAN data network of your vehicle. It also comes with a service/valet mode, which allows you to temporarily start your car while it's in garage for cleaning or servicing.
Easy to install
The Ghost immobiliser is a cutting-edge security tool that shields your vehicle from cloning, hacking, and key theft. It is a unique PIN code system that is integrated into the ECU of your vehicle which makes it extremely difficult for thieves to identify or tamper with. It's not noticeable and does not require any sensors or special keys. It's also cheaper than replacing an ECU, or installing a key fob. You could even lower your insurance premiums.
When installing a Ghost 2 immobiliser, be sure to follow the manufacturer's directions carefully. This will ensure that the device functions properly and efficiently. Test the system following installation by entering the PIN and starting the car. Regular testing will help you identify any problems before they get worse.
Check the location of the the CAN H and CAN L wires prior to starting the installation. They are essential for powering the immobiliser so it is vital that they are connected properly. It is also a good idea to label the wires so that it makes it easier to locate them when installing the device. Once you have identified the locations of these wires and connected them to a permanent 12V power source as well as an earthing point. Be sure to utilize a fuse tap if necessary to protect the connections from short circuits or damage.
After connecting the wires, neaten the wires with cable ties to avoid interference. You can also cover the connections using insulation tape or heat-shrink tubing. This will shield the device from electrical shorts, and will extend the life of the device. It's a great idea to test your Ghost 2 immobiliser once the wiring is secured.
In situations where you have to hand over your vehicle, for example for servicing or valet parking or valet parking, the Ghost 2 immobiliser has a service mode that temporarily disables the PIN code sequence. To activate autowatch ghost immobiliser , press the brake pedal while holding the accelerator for a number of times that is equal to the first number of the emergency code. The system will then enter service mode, which can be confirmed by flashing the indication signal 5 times.
It is simple to change PIN codes
Ghost 2 immobilisers are an excellent method of protecting your vehicle from theft. It is installed discreetly within the vehicle, and can only be accessed through a specific code. The device communicates with the vehicle ECU through its data bus. It does not rely on radio frequency signals like aftermarket alarm systems or traditional Thatcham immobilisers do. This makes it difficult for thieves to detect the click of a conventional immobiliser relay, or to add new key fobs. The control unit is hidden in the vehicle's wiring or dashboard, and isn't physically altered to reset the system.
The ghost 2 immobiliser is connected to your vehicle's CAN Data network and uses existing buttons on the steering wheel, door panels and centre console to create an individualised sequence of up to 20 button presses which must be entered prior to the engine can start - just like a PIN code. auto ghost immobiliser is reprogrammable and doesn't require wire cutting during installation. You can even start your car in Valet or Service mode when you give it to a mechanic complete the work.
The application can also be used to block your PIN number if you've lost your keys, or change it. This feature is particularly useful when you have lent your vehicle to someone else for valet parking or servicing since it prevents them from starting your car and taking it away without consent. It is also inaccessible to professional thieves since it doesn't make use of any circuit cuts or radio frequencies.
The capability of the immobiliser to stop relay thefts is a great feature. Relay theft is among the most popular methods of car theft. Criminals gain access to your car's diagnostic ports, then alter the signal sent by the car's ECU to fool it into thinking that an authentic car key is present. This is how traditional immobilisers can be bypassed, but with a ghost 2 immobiliser, the signal is blocked before it reaches the ECU.
Simple to use app
Ghost 2 is a revolutionary immobiliser that protects your car from key-cloning, hacking, and key theft. It connects to the CAN data network of your vehicle and requires a PIN code in order to start the engine. It also deters thieves from using signal spoofing and device spoofing, which are both common tactics employed to steal vehicles.
The system is simple to use and works like an auto alarm that is used in a normal way. Once you install it, you can generate a unique PIN sequence that can be up to 20 digits in length and must be entered before the vehicle starts. This will protect the vehicle from being stolen even if your keys get removed. You can disable the system by downloading an app for your phone.
Contrary to other systems it is completely silent and does not emit any radio frequency signals. It is a quiet, weatherproof device that can be positioned anywhere in your vehicle. It can be hidden beneath the dash, steering wheel, or even the door panels. It communicates via the CAN data loop to your ECU and is not affected by the diagnostic tools used by thieves to identify security systems. It is not affected by jamming devices which disguise codes.
It is a covert installation that does not require any wire cutting or modification to the car, and it can be utilized as an anti-theft system for all cars. Its technology has been proven to be efficient, and it is in line with TASSA Standards. The Ghost is a good choice for classic or sports cars. It can be used as a method to protect vehicles hired on websites like Turo.
The Autowatch Ghost 2 is the next generation of car immobilisers. This system is invisible to thieves, and blocks them starting your vehicle without your PIN, or unless they have been authorized by the app. It doesn't emit radio frequencies or other signals that scanners can detect. Installation is fast and simple. The app is simple to navigate and offers a user-friendly interface that makes it easy to configure and use. It also includes a GPS tracker to assist police locate and recover the vehicle.
Easy to reset
It is possible to secure your vehicle from theft by using a ghost 2 immobiliser. It works with your vehicle's ECU to create a barrier that thieves are unable to penetrate without the correct PIN. The device is also TASSA-certified, which means that it is acknowledged by insurance companies. It's a useful tool to deter theft of your car and will save you money in the long run.
Contrary to traditional alarms/immobilisers which require circuit cutting and circuit cutting, the Ghost system is connected directly to the vehicles CAN data network and works with the existing buttons on the dashboard as well as the steering wheel. You can set up an individual PIN sequence, which can be up to 20 presses in length. This PIN is required to be entered before the engine can be started like the credit card's PIN. The Ghost system is inaccessible to thieves and there aren't LEDs to indicate its presence. This makes it the most efficient aftermarket CAN-bus immobiliser available today.
The Ghost system has another advantage that it does not transmit radio frequency signals. This means it cannot be detected by thieves or snatched up. This is a deterrent to cloned key attacks and relay attacks, as and the typical method of hacking into a car's computer system using its CAN bus by scanning for signals. Additionally, the Ghost system is designed to be completely hidden within the vehicle, and there are no lights or signals to indicate its presence.
The system features the option of a Transport Mode which disables the Ghost System. This is beneficial for situations when you require a temporary deactivation of Ghost, such as when transporting or maintaining your vehicle. This mode is less effective than Service Mode as it doesn't deactivate the Ghost system if you exceed 31 mph in 15 minutes.
To reset your ghost 2 immobiliser, you will need to have the emergency code, which you can obtain from your installer. The code is typically hidden beneath the scratch-off portion of the card that came with the installation. You should keep the emergency code secure and keep it in a place that is secure, such as your wallet at home.